Matinum

Taking Charge of Your Health


Steel is the most important material to human
society. It has been the skeleton of human industry
for centuries, and the advent of the methods to mass produce it from iron ore was the impetus
to transform human society from a mostly agricultural lifestyle to urban industrialisation. It forms the backbone of our skyscrapers,
it paves the way for our railways, it shapes the engines that powers our society, and the
very tools that forge these objects are made from steel. We have spoken before about how the refining
processes of iron determines whether the resulting material will be steel or iron and how the
exact percentage of carbon present in the material has dramatic results on the final
material properties, and how the production methods through time has taken steel from
an expensive material reserved for swords, armour and toolmaking, to one that has permeated
into nearly every technology we use in our lives. But I failed to tell why that simple addition
of carbon has such a huge effect on the iron, turning it from a relatively weak material
to one capable of launching an industrial revolution, which is what we are going to
learn about today. Much of our knowledge in crafting steel was
passed down over the centuries from blacksmith to blacksmith, creating tools for their communities,
so to learn more about this amazing material and how blacksmiths carefully tailor it’s
material properties, I visited Alec Steele’s workshop to create my own knife from scratch. We started our forging process with round
stock 1055 steel with 0.55% carbon content, placed it in the forge and gradually shaped
it with a power hammer to a rectangular bar that could be more precisely shaped into the
shape of our blade using a 3 pound hammer that my wee arms struggled to swing after
an hour. Once we had roughed out the shape we began
to grind and refine our blade. Eventually producing our blade blank that
would later be grinded to it’s final shape, but before that could happen we needed to
perform some metallurgy wizardry through the heat treatment process. To drive home how important this step is,
we tested 4 samples of the same material at different stages of the heat treatment process. This was our sample before the heat treatment
process, which you will quickly see was the weakest of the bunch. This is the normalised sample, which was ductile
with a low yield stress. It took several hammer blows, which it absorbed
through plastic deformation, not ideal characteristics for a sword or knife. Next we tested our quench hardened sample,
which is stupid and dangerous and should not be tried at home. This fractured explosively and tore a hole
through Alec’s reflector. Finally we tested the tempered material, which
absorbed every hammer blow with minimal plastic deformation and only broke when we cut a notch
into the material to create a stress concentration point. This material is tough, capable of absorbing
energy without deforming permanently, and hard allowing it to resist damage to the cutting
edge. It is the ideal material for a blade. If any of these terms confused you, I created
a video called Material Properties 101 that you can check out to get a better understanding
of material property terminology. So how can the same steel alloy change so
radically by simply applying heat? Well this is the magic of the iron carbon
alloy. We can careful control how the internal metallic
crystal structure forms with heating and cooling cycles. First let’s see how adding carbon to iron
affects it’s crystalline structure. With no carbon present pure iron will form
a crystal structure called body centred cubic with an iron atom at each of the eight corners
and another in the centre. Each crystal structure has a direction it
most easily wants to deform, called a slip plane. For body centred cubic the slip plane occurs
along this planes. Metals with Body centred cubic crystals like
iron and tungsten tend to be harder and less malleable than metals with face centred cubic
crystals like aluminium, lead and gold. When a metal is cooling, these crystals grow
from individual nucleation points and form grains where each grain has the same orientation
of slip plane but neighbouring grains may not have the same slip plane. Let’s think about this 2 dimensionally,
when a force is applied, the grain wants to slip in a particular direction, and passes
the force onto the next grain in that direction too, but this grains slip plane is at a different
angle, so that force needs to be greater in order to cause deformation. It’s like trying to push a train down a
railway track, by pushing on its side. It’s not going to go anywhere easily. So smaller and more numerous grains results
in a stronger material. Pure iron tends to always has the same crystal
structure as it cools and it’s crystal structure doesn’t change meaningfully with heat treatment. This is where alloying with carbon comes in. To explore this let’s look at our phase
diagram for carbon steel. On this diagram we have our carbon content
percentage on the x-axis and the temperature of the metal on the y-axis. This tells us the crystalline structure of
the metal at various temperatures and carbon contents. On the left hand side we have pure iron, which
as we explained earlier forms only one crystal structure, called ferrite. As we move across the diagram to the right
hand side, less and less of the crystal structure forms ferrite, and more forms an iron carbide
alloy, commonly called cementire. Now if we move up in temperature we start
to see these lines that represent transitional temperatures, where the crystal structures
of the steel begin to transform into a new crystal structure called Austenite. Moving further up again we see lines representing
the transition of the material to a liquid state. Austenites primary difference to ferrite is
that it forms that face centred cubic crystal structure that we saw early, while ferrite
is body centred cubic. And while this packing pattern is denser than
body centred cubic, it does open up spaces in the crystal structure that interstitial
carbon atoms, which are smaller than iron, can snuggly fit. Allowing austenite to have a higher solubility
to carbon over ferrite. Using all of this information, let’s take
our 1055 steel with 0.55% carbon content and see how it transforms from the start of our
heat treatment cycle to the end. The first step is called normalisation. Normalisation is primarily functions to relieve
internal stresses and strains that formed during the forging process and return the
material to its original crystal structure before forging began. It’s effectively a reset button for the
steel and creates nice even grain size and distribution, increasing its strength. Here we placed the knife blank inside a steel
tube to prevent the metal from receiving heat directly from the flame, but instead a more
even radiative heat from the tube. Once it reaches this transition temperature
we let it soak to give the crystal structure time to settle. The next step in normalising is to allow the
steel to slowly air cool. What happens now depends on the carbon content. If we take a 0.8% carbon steel, no hang on
we’re gonna need a bigger graph for this, If we take a 0.8% carbon steel and cool it
to it’s through transitional temperature the austenite and the interstitial carbon
will slowly transform to a mixture of ferrite and cementite, which takes this laminar structure
called pearlite. Pearlite only forms at a 0.8% carbon solution Now if we take a 0.55% 0.2% steel, like the
one we used. And slowly cool it, to its first transitional
temperature here. Where ferrite first begins to form, ferrite
is pure iron so as it forms the carbon percentage begins to rise, this will continue to happen
until the remaining austenite has a carbon percentage of 0.8% and it will then form pearlite
from this point on. This forms a crystal structure dominated by
ferrite, showing here as a lighter colour, surrounded by the darker pearlite. Comparing these microstructures to another
2 we can see the effect carbon has on the microstructure. Here we have pure iron, with 100% ferrite,
showing as this light colour, you can even see the grain boundaries. This is a 0.5% carbon steel similar to ours,
where a very small amount of ferrite formed before we reaching the point of pearlite formation,
and this is 0.8% carbon steel where the entire structure is pearlite, with our previous example
showing pearlite under 500 times magnification where you can readily see that laminar structure. How Pearlite strengthens steel is not well
understood. It has little effect on the steels stiffness,
but increasing the pearlite content has dramatic effects on the materials yield point, making
it much more capable of absorbing energy without permanently deforming. But we can increase the materials stiffness
and hardness with our next step. If we heat the metal back up to form austenite
once again, but this time instead of letting it cool slowly, we rapidly cool it in oil,
while casually burning your arm hair off and barely flinching, the carbon atoms that spread
out throughout the hot austenite structure cannot diffuse out of the crystal lattice
to form cementite, and instead gets stuck in solution, creating a new crystal structure
called martensite. This crystal structure has a huge amount of
internal stretching. In part because the carbon trapped within
the crystal structure causes the crystal lattice to deform, but also because during the rapid
cooling the surface cooled much faster than the internal material. This causes internal tension in the material. These internal strains make it harder for
additional deformation to occur, but this does not make the material stronger. It simply means it will not stretch and bend
before breaking, and when it finally does fracture all of this internal tension is suddenly
released in an explosive expansion. If you have watched Smarter Every Days video
on the Saint Rupert’s Drop, you will have seen this principle demonstrated in incredible
slow motion. This material property is called hardness,
and we want our cutting edge to be hard to resist damage when cutting, but we do not
want our entire blade to be hard as it will not be able to absorb a lot of energy. It needs to be able to dissipate some of that
energy through heat and deformation. This is where the final step of the process
comes in, called tempering. Tempering raises the temperature enough to
allow the carbon trapped in solution to escape, we just used an oven set at 200 degree, the
carbon then coalesces to form cementite once again, but instead of forming pearlite like
before. It gathers in globules surrounded by ferrite. Tempering also relieves some of that internal
tension caused by the rapid cooling.This reduces the hardness, but increases toughness. This produces a material that has the perfect
balance of characteristics between the normalised material and the hardened material. It is ductile enough to absorb hammer blows
without shattering, but strong enough to not permanently deform, and with enough hardness
to ensure it doesn’t gather damage on the cutting edge. This process gave our steel the perfect material
properties and a lot of that is thanks to the quality of the steel we started off with. Learning these skills with Alec was a lot
of fun and I highly recommend you check his channel out. His incredible attitude to work really inspired
me to start learning some new hands on skills this year and I am hoping to start that off
by learning how to programme and create robotics with an arduino. This course I found on skillshare is the perfect
jumping off point for anyone looking to learn the same skills. Skillshare is home to thousands of other classes
in graphic design, animation, web development, music, photography, video game design and
more. These days you can teach yourself pretty much
any skill online and Skillshare is a fantastic place to do it. With professional and understandable classes,
that follow a clear learning curve, you can dive in and start learning how to do the work
you love. .
A Premium Membership begins around $10 a month for unlimited access to all courses, but you
can get your first 3 months for just 99 cent if you sign up with this link.This offer was
supposed to be only valid until the end of Jan, but I talked to Skillshare and was able
to get this extended for ye until Feb 15. In those 3 months you could easily learn the
skills you need to start a new hobby or business. So ask yourself right now. What skill have you been putting off learning. What project have you been dreaming of completing,
but you aren’t sure if you have the skills to do it. Why not start right now and sign up to Skillshare
using the link below. You have nothing to lose and a valuable life
skill to gain. As usual thanks for watching and thank you
to all my Patreon supporters. If you would like to see more from me, the
links to my twitter, facebook and instagram pages are below.

100 thoughts on “Heat Treatment -The Science of Forging (feat. Alec Steele)

  1. Mmm!! Hardness is defined as resistance to Indentation and measured on the Rockwell scale chalk =1 Cdiamond =90.by hitting steel any C content you will alter the hardness of the sample it's called work hardening

  2. I have just traveled by time machine! That's what an important part of my engineering school was about! Greetings from the Czech republic!

  3. Material Science and Engg. Course
    Duration: One Semester | Learning: NIL
    Real Engineering YouTube Channel
    Duration: ~12 mins/ video | Learning: Everything

  4. but how carbon content of steel increases while it cools %0.5 to %0.8 how's that even possible. doesnt free carbon atoms that are not forming carbide count?

  5. Gonna say this one more time,old blacksmiths received information directly from the gods of war to the brain, or some got their mead overdosed with knowledge 🙂

  6. Structure and Properties of Materials 101. This is LITTERALLY one of the classes I've taken for Mechanical Engineering

  7. So hypothetically. What if we could forge a metal with a 100% perfectly structured lattice? Like how carbon nano tubes look, perfect crystals?

  8. At around 6:45, how did the alloy gain more carbon and lose iron? I thought when you cool and alloy it has to go straight down the graph?

  9. I absolutely love your break down of why this process works…I may have to watch it more than once for it to sink in but thank you for the video! Keep up the learning curve 🙂

  10. Can I come and work with you for a weekend? I've never been to Ireland…love fire…knives…And hard work

  11. Fantastic video! Many years ago I sold industrial metal forgings capable of up to 300,000 lbs of tensile strength, which were case hardened and drop-forged. I knew just enough to be helpful selling the products, but I learned more about crystal structure in the last 5 minutes as I did in that decade! Thanks for sharing.

  12. Hey! I've watched this video a couple times and the part about how grain structures transfer loads was pretty cool. I found an old video where they go into detail about this. At 7 min. in they talk about the several theories proposed to explain why cold working aluminum hardens the metal. There are three theories posed, and being that the video is pretty old I would think they have figured this out but cant find any reference online. As a materials engineer I assumed you might know more: https://www.youtube.com/watch?v=fJyD8R8zFLE

  13. What is the difference between quenching the steel into oil when it is glowing hot vs hot but not glowing?

  14. Steel hasnt been the skeleton of human industry for centuries, maybe 150 years at most. Urban settings have existed for thousands of years the world over, but its only the form that has changed, and the molecular structure. Still, nice vid. ^~^

  15. As a farrier I've learnt a bit about metallurgy, I mean, we know about hardening and tempering and carbon contents of steels etc, but this blew my mind!

  16. Fellow Engineer here… This video may be the best presentation I've ever seen as to how alloying and heat treating steel works. If anything my only objection is that this isn't something limited to "forging" as we do almost all the same steps when machining from wrought steel (some of which may have already been performed at the mill).

  17. cook it and let it air cool
    cook it again but cool it rapidly in oil
    cook it again, low temp – for TEMPering

  18. This video was perfunctory and inaccurate to me as a scientist. This old video explains much better for those who are really interested: https://www.youtube.com/watch?v=uG35D_euM-0

  19. Must EVERY damn channel pimp Skill Share?! Their efforts to get their name out there is making people sick of them.

  20. Great vid but I would've loved to see a TTT diagram being used as well when discussion how to make different % of phases

  21. This helped me understand why when I just heated up my small blame and cooled it quick it would shatter with enough force

  22. What is the point of editing out all of the pauses between the sentences? It just becomes non-stop rambling. Next!

  23. On a video featuring Mike Boyd, Alec makes him twist the material. Why?
    https://www.youtube.com/watch?v=12vfxYs6F7E around 4:20 (Don't do drugs)

  24. I know that a prince rupert's drop and steel have different molecular structures, but has anyone ever attempted to temper a prince rupert's drop to see if it would produce a similar result to the steel?

  25. if there is carbon being put into the steal, how come rust never shows any black spots?
    are you sure it's high carbon steel and not high hydrogen infused steel?

  26. Why does the metal get heated up after already being cooled to form perlite? doesn't heating it up and quenching it undo the previous perlite crystal structure and make that step pointless? Asking as an undergrad who wants to actually understand this process, thanks.

Leave a Reply

Your email address will not be published. Required fields are marked *